Barco FLM R22+ Guia do Utilizador Página 230
- Página / 243
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
22. Specifications
Specifi cations
• SD SMPTE 259M-C and HD SMPTE 292M input data
• 2 inputs (BNC), 1 active loop-through output (BNC) of selected input
• Automatic selection of active input with manual override
• 10 bit digital output
• Diagnostic LED’s on front panel:
- Green LED: Lights up in case input module is selected
- Yellow LED: Lights up in case sync detected
• SDI: 270 Mbit/s transmission (SMPTE 259M-C).
• SDI: 525/625 interlaced.
• Coax (75 Ohm).
• Supported HDSDI standards:
- Progressive:
o
1280x720/60/1:1/ (SMPTE 296M)
o
1280x720/59.94/1:1/ (SMPTE 296M)
o
1920x1080/30/1:1/ (SMPTE 274M)
o
1920x1080/29.97/1:1/ (SMPTE 274M)
o
1920x1080/25/1:1/ (SMPTE 274M)
o
1920x1080/24/1:1/ (SMPTE 274M)
o
1920x1080/23.98/1:1/ (SMPTE 274M)
- Interlaced:
o
1920x1035/60/2:1/ (SMPTE 260M)
o
1920x1035/59.94/2:1/ (SMPTE 260M)
o
1920x1080/60/2:1/ (SMPTE 274M)
o
1920x1080/59.94/2:1/ (SMPTE 274M)
o
1920x1080/50/2:1/ (SMPTE 274M)
o
1920/1080/50/2:1 (1250)/ (SMPTE 295M)
o
1920x1080/24/Segmented/ (SMPTE 274M)
o
1920x1080//23.98/Segmented/ (SMPTE 274M)
22.4 Specifications FLM DVI input
Input front view
Sync OK
Sel
DVI input
Image 22-3
Specifi cations
• DVI type: DVI-I (DVI-Integrated), but the analog signals are not supported. Single-link configuration.
• Single link dvi for pixelclocks up to 165MHz
• Vertical frequencies: 24 - 75 Hz
• Horizontal frequencies: 20 - 90 kHz
• Supported resolutions: up to UXGA (1600 x 1200) at 60 Hz.
• Cable lengths: up to 3 meter at UXGA speed.
• Compliance: DDC2B support according to VESA EDID Version 1.2
• Diagnostic LED’s on front panel:
- Green LED: Lights up in case input module is selected
- Yellow LED: Lights up in case sync detected
226
R59770179 FLM R22+ 15/03/2010
- FLM R22+ 1
- TABLE OF CONTENTS 5
- Table of contents 6
- 1. SAFETY 9
- 1. Safety 10
- 2. GENERAL 15
- 2.2 Unpacking the projector 16
- 2.3 Box content 17
- 2.4 FLM flight case 18
- 2.5 Projector configurations 18
- 2. General 19
- 3. PHYSICAL INSTALLATION 23
- 3. Physical installation 24
- 3.2 Lenses 27
- 4. STACKING FLM PROJECTORS 35
- 4. Stacking FLM projectors 36
- Inclination 37
- 5. CONNECTIONS 39
- 5. Connections 40
- 5.3 Communication connections 42
- 6. GETTING STARTED 47
- 6. Getting started 48
- 6.3 Operating the projector 49
- Temperature error DMD 50
- 6.3.3 Switching to standby 50
- How to switch to standby? 50
- 6.4 Using the RCU 51
- Hardwired to the XLR input 52
- 6.5 Quick setup adjustments 53
- 6.6 Projector Address 56
- 6.7 Source selection 57
- 6.8 Controlling the Projector 58
- 7.1 About the adjustment mode 59
- How to make an adjustment? 60
- About a shortcut key 60
- 7.8 Menu memory 61
- 8. INPUT MENU 63
- 8. Input menu 64
- 8.3 Input locking 65
- 8.4 Minimum delay 67
- 8.5 Native resolution 67
- 8.6 Source switching 69
- 8.7 No signal 69
- 9. IMAGE MENU 73
- 9.3 Image Settings 74
- 9. Image menu 75
- 9.4 Aspect ratio 86
- 9.5 Timings 87
- 9.6 Image files services 92
- 9.7 Save custom settings 97
- 10. LAYOUT MENU 99
- 10. Layout menu 100
- 10.3 PIP window 104
- 10.4 Layout file services 110
- 10.5 Zoom - Focus 113
- 11. LAMP MENU 115
- 11.3 Lamp power 116
- 11. Lamp menu 117
- 11.5 CLO target 118
- 11.6 Lamp Identification 118
- 11.7 Z-axis adjustment 119
- 12. ALIGNMENT MENU 121
- 12.2 Orientation 122
- 12.3 Lens adjustment 123
- 12.4 Side keystone 124
- 12.5 Warp geometry settings 125
- 12. Alignment menu 126
- 12.6 Contrast enhancement 134
- 12.7 Blanking 134
- 12.8 Gamma 136
- 12.9 Internal pattern 136
- 12.10 Color space 137
- 12.11 ScenergiX 138
- 13. PROJECTOR CONTROL 149
- 13.2 Projector address 150
- 13. Projector control 151
- 13.3 Serial communication 152
- 13.4 Network 153
- 13.5 IR control switching 157
- 13.6 Art-Net DMX 157
- 13.7 Buttons 162
- 13.8 Menu position 164
- 13.9 Local LCD 165
- 13.10 Language selection 166
- 14. SERVICE MENU 169
- 14.2 Identification 170
- 14.3 Diagnosis 171
- 14. Service menu 172
- 14.4 Convergence 176
- 14.6 Restore factory defaults 178
- 14.7 Reset formatter 179
- 14.8 Save custom settings 180
- 14.9 Refill mode 180
- 14.10 Broadcast mode 181
- 14.11 USB memory 182
- 15. MAINTENANCE 185
- 15. Maintenance 186
- 15.5 Cleaning the lens 188
- 16. SERVICING 189
- 16. Servicing 190
- About this chapter 197
- Overview 197
- Necessary tools 197
- Image 17-5 199
- Image 17-6 199
- 18. DIMENSIONS 205
- 18. Dimensions 206
- 19. STANDARD SOURCE FILES 209
- 19. Standard Source Files 210
- 20. DMX CHART 211
- 20.2 DMX chart, Extended 212
- 20.3 DMX chart, Full 213
- 20. DMX chart 214
- 21. TROUBLESHOOTING 217
- 21. Troubleshooting 218
- 22. SPECIFICATIONS 225
- 22. Specifications 226
- 23. ORDER INFORMATION 233
- 23. Order information 234
- GLOSSARY 235
- Glossary 236
- Revision Sheet 243
Manuais e produtos relacionados com Projetores de dados Barco FLM R22+
Projetores de dados Barco Galaxy NW-7 Guia do Utilizador
(183 páginas)
(183 páginas)
Projetores de dados Barco SLM G10 Manual do Proprietário
(159 páginas)
(159 páginas)
Projetores de dados Barco F50 Manual do Utilizador
(66 páginas)
(66 páginas)
(87 páginas)
Projetores de dados Barco RLM W6 Guia do Utilizador
(57 páginas)
(57 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais