Barco MD-4221 Manual do Utilizador

MD-4221 42” HD MEDICAL LCD MONITOR User manual

10 Servicing Do not attempt to service the apparatus yourself as opening or removing covers may expose you to dangerous voltages or other hazards,

11 FCC Information This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC

12 RF Emissions CISPR 11 Class B Harmonic emissions IEC 61000-3-2 D Voltage fluctuations IEC 61000-3-3 Complies including domestic establishments

13 Electromagnetic compatibility Warning When this device is connected with other electrical equipment, leakage currents may be additive. To mini

14 Recommendations for using your display system 1. Optimize the lifetime of your display Enabling the Display Power Management System (DPMS) of y

15 • Do not apply pressure to the screen or touch the screen with bare fingers or objects. Pressure can affect image quality. Cosmetics and oils

16 Serial Number. Top-Bottom. Fragile. Do not get wet. Maximum Stacking. Indicates proof of conformity to applicable European Economic Commu

17 Introduction Quick Startup 1. Connect the power supply to the display via the power plug. 2. Plug into the AC inlet with power cord cable. 3.

18 Connectors

19

2

20 Mechanical product drawing

21 Controls Remote control Key Description F1 Input Selection, same as input button on user con-trols F2 PiP Button on OSD F3 PiP Swap F4 No

22 OSD buttons position OSD Button Function An 8-button keypad, located on the right hand side of the display, allows the user to make adjustment

23 ● Power LED Green : Normal mode Amber: Standby mode Amber: Soft power-off ● On-Screen Display (OSD) Function Button 1. POWER : Turns ON/OF

24 On-Screen Display Menus Adjust <VGA Analog/RGBS input> <SDI input> <DVI input>

25 BRIGHTNESS Increase or decrease the brightness. (Range : 0~100) CONTRAST Increase or decrease the Contrast. (Range : 0~100) SHARPNESS (1) Ad

26 Advanced <DVI and SDI inputs> <Other inputs> SCALING Change the image size (Best Fit, Fit Width, Fit Height,Native,Fu

27 Setup LANGUAGE Change the OSD language. (8 languages) BACKGROUND Set the Background color RS-232 BAUDRATE Change RS232 BAUDRATE (115200,384

28 PIP LAYOUT Change the OSD layout. (Single, PIP, PBP1, PBP2) SOURCE 1 Change the primary source. SOURCE 2 Change the secondary source. SIZE

29 OSD functions description Menus Function Descriptions BRIGHTNESS Setting the brightness too high or too low will decrease the amount of visib

3 Copyright notice This document is copyrighted. All rights are reserved. Nor this document, nor any part of it, may be reproduced or copie

30

31

32

33

34 Standard signal table PC modes supported Resolution Horizontal Fre-quency (KHz) Vertical Frequency (Hz) Clock Frequency (MHz) 640 X 350 @7

35 SDI video format Output Signal Description SMPTE-274M 1080i (60 / 59.94 / 50) 1080p (30 /29.97 / 25 / 24 / 24sF / 23.98 / 23.98sF) SMPT

36 Signal connector pin assignments VGA (15-pin D-sub) Pin No. Assignment Pin No. Assignment 1 Red 9 No Connection 2 Green 10

37 7 DDC Data 19 T.M.D.S. Data0 Shield 8 No Connection 20 No Connection 9 T.M.D.S. Data1- 21 No Connection 10 T.M.D.S. D

38 RS232C (D-Sub 9-pin) Pin No. Assignment 1 No Connection 2 TXD 3 RXD 4 No Connection 5 Ground 6 No Connection 7 No Conn

39 RGB HV/RGBS/YPbPr (BNC) Assignment Pin No. RGBS Y Pb Pr 1 Red Pr 2 Green Y 3 Blue Pb 4 H-Sync / C-Sync No Connection

4 Table of Contents Table of Contents ... 4 Preface...

40 Specifications Model MD-4221 Type TFT-LCD Screen Size 42 inch Maximum Resolution 1920 X 1080 @ 60Hz Pixel pitch 0.4845(H) mm

41 BARCO MID GENERAL WARRANTY TERMS AND CONDITIONS Applicable from Jan 1st 2008 ARTICLE 1: PRODUCT WARRANTY Barco nv, Medical Imaging Division

42 an authorised service centre). 1.4 Replacement parts used shall be new or equivalent to new parts for the revision level of the equipment. A re

43 Normal wear and tear, use under circumstances exceeding specifications, such as use in dusty environment or under excessive temperature condit

44 v. LCD luminance uniformity that is in within the product specifications or luminance uniformity performance that is inherent to LCD tech

45 ARTICLE 5: DISCLAIMER OF WARRANTIES BARCO NV, MID DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANT

46

B410615-01 August 2009 Barco N.V. President Kennedypark 35 B-8500 Kortrijk, Belgium visit us at the web: www.barco.com Support helpde

5 Preface Important notice Notice Although every attempt has been made to achieve technical accuracy in this document, we assume no responsibilit

6 Safety Instructions On Safety 1. Before connecting the AC power cord to the DC adapter outlet make sure the voltage designation of the DC adapt

7 Warning When necessary, carry this product with at least 2 persons, using both handles on left and right side of the product. If you want the p

8 Caution To prevent fire or shock hazards, do not expose this unit to rain or moisture. Also, do not use this unit's polarized plug with

9 Use the proper power cord with correct attachment plug type. If the power source is 120V AC, use a power cord which is a Hospital Grade Power C